Colour Security Camera designed to blend with surroundings in domestic and commercial applications this Camera can easily be added to an existing Security system, simply connect Video Output to an unused Security DVR Video input.

Connect to the Composite Video Input (AV, Yellow RCA socket) on most TVs and Domestic or commercial Recording Devices, if required a Microphone can be easily added and a single small diameter Cable used to carry Video, Audio & Power 20 or more metres.

Sony's latest Super-HAD-II High Resolution 437 664 Pixel CCD Image Sensor unlike some cameras that utilise a CMOS image sensor this Security Camera has a Sony Charge Coupled Device with more than 750 horizontal pixels and significantly higher Sensitivity and higher Signal-to-Noise ratio than a CMOS sensor.

Unlike some, this Camera employs the full potential of the 437 664 pixel image sensor by utilising a Wide-Bandwidth Digital Signal Processor capable of 540 + Horizontal Television Line (540 H-TVL) video output.

Image Device: 795 (H) x 596 (V) 473 820 Pixel 752 (H) x 582 (V) effective ⅓" SONY ICX639BKA Super HAD II CCD. *CCD=CCD image sensor "Super HAD CCD II" is a trademark of Sony Corporation. The "Super HAD CCD II is a version of Sony's high performance CCD HAD (Hole-Accumulation Diode) sensor with realized sensitivity (typical) of 1000mV or more per 1µm2 (Color: F5.6/ BW: F8 in 1 s accumulation equivalent.)

click on images to enlarge

Colour Day / Night Infrared Light Emitting Diode Infrared Night Vision information 'Primer' here.

Lens: Board Type 3.6 mm Focal Length, there are no Accessory Lenses for this Camera, additional information here.

Scanning System: 2 : 1 Interlace PAL 50 Hz vertical, 15 625 Hz horizontal.

Synchronisation: Internal.

Video Output: 1.14 V p-p Composite Video 75 ohms, suit Australian TV, VCR, AV & Video inputs, BNC socket, ~ 75 cm cable.

Horizontal Pixels: 750 + better than Super-VHS near DVD resolution (this value is provided for comparative purposes only).

Sensitivity: ~ 0.5 lux @ F1.2 (this value is provided for comparative purposes only), 0 lux with LEDs 'ON'. Infrared LEDs illuminate ~ 95% of the Width-of-Vision and are effective up to approximately 15 metres depending on the reflective characteristics of subject.

Light Emitting Diodes: Twenty ~ 850 nm wavelength Infrared, LEDs produce a dull Red visible glow. Automatic Light Sensor switches LEDs On/Off depending on light level.

Automatic Electronic Shutter (AES): 1/50 to 1/100 000 second, 20 milliseconds to 10 microseconds, additional information here.

Automatic Gain Control (AGC): Yes.

Back Light Compensation (BLC): Automatic.

White Balance: Automatic.

Spectral Response: ~ 400 to ~ 1000 nm with an Infrared 'CUT' Notch between approximately 720 ~ 830 nm, additional information here.

Signal to Noise ratio: 48 + dB, measured with AGC off.

Power Requirements: 12 Volts DC Regulated, ~ 90 milliamps (IR LEDs OFF) ~ 170 mA LEDs ON, 2.1 x 5.5 mm DC socket, center pin +,  ~ 75 cm cable.

Dimensions (mm): ~ 93 x 75.

Mass: ~ 200 grams.

Manufacturer: 18+ years experience. ISO 9001, CE, FCC, RoHS certification. OEM & ODM supplier.

Made in China.

Need Sound ? click here

Colour CCTV Day Night Cameras with inbuilt Infrared Light Emitting Diodes "See-in-the-Dark" and produce images when visible illumination is zero.

At average levels of illumination these Cameras produce Colour images, depending on their sensitivity (Lux) at low illumination levels and in total darkness the image is Monochrome.

These Cameras generally have a relatively high sensitivity image sensor and Fixed Iris Lens therefore under high illumination levels images will be overexposed for the reasons outlined here.

Ordinary CCTV Colour Cameras are relatively insensitive to Infrared because they have an IR CUT Filter between the Lens and Image Sensor, this filter excludes Infrared radiation with a wavelength greater than ~ 700 nm that would otherwise adversely affect White Balance, Colour Rendition and Image Sharpness.

Day / Night Colour CCTV Cameras are sensitive to Infrared because they either do not have an IR CUT Filter or utilise a special NOTCH IR CUT Filter that excludes the wavelengths most harmful to colour quality (720 ~ 830 nm) from reaching the Image Sensor.

A Colour Camera that does not have an IR CUT Filter usually has poor colour rendition characterised by a Pink-Red 'tint' when the illumination is InfraRed rich, use of a 'Notch' Filter helps however White Balance, Colour Rendition and Image Sharpness are compromised for Infrared sensitivity. (Image Sharpness can be restored by using a specially designed Lens that corrects for focus shift between Visible and Infrared)

The IDEAL Day / Night Infrared Sensitive Colour CCTV Camera utilises a Lens with an Automatic Iris to cope with high illumination levels - has a large aperture (low 'F' number) to maximise light transmission and is corrected for Infrared:Visible focus-shift, it also utilises a Traditional IR CUT Filter when illumination levels are adequate for Colour and REMOVES the IR CUT Filter when levels are low our Maxi Cameras have these features and are recommended for OPTIMUM results

BETTER SOLUTION: AutoCam-dn - DomePTZ-dn2 - DomePTZ-dn3 have Automatic-Focus to ensure crisp images regardless of illumination source.

Infrared rich light sources include Daylight and most Filament type lamps including common Spot lamps, Tungsten lamps, Halogen lamps, etc.

The majority of Light emitted from 'Cold' type sources such as Fluorescent, Mercury Vapour, Sodium Vapour, etc., is visible, these sources contain little Infrared energy.

"See-in-the-Dark" Infrared capability using a notch (or no) IR-CUT Filter is a trade-off that adversely affects Colour rendition in "Infrared Rich" environments.